;
; tddh.txt - help messages version 2.0
;
TDD
TDD0000?:
TDD0001H: EXPLANATION:  The file specified in the CODE= statement in the
CONFIG.SYS file cannot be found. For example, TOUCOxxx.BIN. (Where
xxx is the microcode level.)
ACTION:  Edit the CONFIG.SYS file and be sure the file name is correct, or
that it exists in the path; then, restart your system.
TDD0002H: EXPLANATION:  You are unable to use your Touch Device
because an error occurred when it attempted to communicate
with the hardware.
ACTION:  Do one of the following:
1. Be sure your system components are powered on.
2. If you are using a Microchannel PS/2, be sure that there is an
ABIOS.SYS file in the OS2 directory.  Then, be sure the line TOUMOUSx.BIO
is included in this file.  If it is not there, add a line with this
file name.
NOTE:  x is the ABIOS level that has been copied onto your system.
3. If after verifying the above, the error still occurs:
 - Power off your system and display.
 - Check to be sure that the cable is connected correctly to the
   PS/2 mouse port connector at the back of the system unit.
 - Restart your system.
4. If the error occurs again:
 - Insert the Reference Diskette and run the diagnostics.
5. If this does not solve the problem, contact your service or sales
representative.
TDD0003?:
TDD0004?:
TDD0005?:
TDD0006?:
TDD0007?:
TDD0008?:
TDD0009H: EXPLANATION:  The DEVICE= statement in CONFIG.SYS for the
Touch Device is missing the CODE= parameter.  This is required to
tell the device driver where the microcode file for the Touch Device
is located.
ACTION:  Do the following:
1. Locate the TOUCOxxx.BIN file on your hard disk.
2. Edit the CONFIG.SYS file and add:
   DEVICE=PDITOU0x.SYS CODE=TOUCOxxx.BIN
3. Restart your system.
 
NOTE:   xxx is the microcode level that is displayed when the code is being
downloaded during device driver initialization.
TDD0010H: EXPLANATION:  The filename is too long in the CODE= parameter
of the DEVICE= statement in the CONFIG.SYS file.
The maximum file name length is 8 characters, and must be followed with a
.BIN extension.  For example, xxxxxxxx.BIN
ACTION: Edit the CONFIG.SYS file and correct the file name; then,
restart your system.
TDD0011?:
TDD0012?:
TDD0013?:
TDD0014?:
TDD0015?:
TDD0016?:
TDD0017?:
TDD0018?:
TDD0019?:
TDD0020?:
TDD0021?:
TDD0022?:
TDD0023?:
TDD0024?:
TDD0025?:
TDD0026?:
TDD0027?:
TDD0028?:
TDD0029?:
TDD0030?:
TDD0031?:
TDD0032?:
TDD0033?:
TDD0034?:
TDD0035H: EXPLANATION:  The DEVICE= statement in CONFIG.SYS
for the Touch Device is missing the INIT= parameter.
Default values were used.
ACTION:  Do the following:
1. Edit the CONFIG.SYS file and add:
   INIT=OS2\TOUCH.INI to the DEVICE= statement.
2. Restart your system.
TDD0036H: EXPLANATION:  The filename is too long in the INIT= parameter
of the DEVICE= statement in the CONFIG.SYS file.
The maximum file name length is 8 characters, followed by a 3
character extension.
The default filename is \OS2\TOUCH.INI.
ACTION:  Do the following:
1. Edit the CONFIG.SYS file and add:
   INIT=OS2\TOUCH.INI to the DEVICE= statement.
2. Restart your system.
TDD0037H: EXPLANATION: The file containing the Touch Device
initialization data in the INIT= parameter cannot be found.
The default filename is \OS2\TOUCH.INI.
ACTION:  Do the following:
1. Edit the CONFIG.SYS file, and be sure that the
   filename is entered correctly and that it exists
   in the specified path.
2. Restart your system.
TDD0038H: EXPLANATION:  The INIT= parameter in the Touch Device
DEVICE= statement in the CONFIG.SYS file refers to the TOUCH.INI
initialization file which contains a syntax error.
The default values were used.
ACTION:  Reconfigure Touch Device support using the Touch Control panel.
TDD0039H: EXPLANATION:  The INIT= parameter in the Touch Device
DEVICE= statement in the CONFIG.SYS file refers to the TOUCH.INI
initialization file which could not be processed because the
file could not be opened.
The default values were used.
ACTION:  Do the following:
1. Edit the CONFIG.SYS file, and be sure that the
   filename is entered correctly and that it exists
   in the specified path.
2. Restart your system.
TDD0040?:
TDD0041H: EXPLANATION:  The INIT= parameter in the Touch Device
DEVICE= statement in the CONFIG.SYS file refers to the TOUCH.INI
initialization file which contains a line with invalid values
for the parameters.
ACTION:  Touch Device support using the Touch Control panel.
TDD0042H: EXPLANATION:  The INIT= parameter in the Touch Device
DEVICE= statement in the CONFIG.SYS file refers to the TOUCH.INI
initialization file which contains a line with a duplicate parameter.
ACTION:  Reconfigure Touch Device support using the Touch Control panel.
%0
