IBM ThinkPad                                                   July 10, 2001
OS/2 Warp Version 4 Install Disk 1 Update and Install Disk 2 Update

Version 1.06 : OS/2 Warp Version 4 Install Disk 1 Update
Version 1.02 : OS/2 Warp Version 4 Install Disk 2 Update
======================================================================


What These Diskettes Do
-----------------------
IBM ThinkPad OS/2 Warp Version 4 Install Disk 1 Update:
------------------------------------------------------------------------------
The IBM ThinkPad OS/2 Warp Version 4 Install Disk 1 Update is a
replacement of IBM OS/2 Warp Version 4 Install Disk 1.  This disk 
fixes the following problems.
  - OS/2 Warp Version 4 cannot be installed on hard disks that have 
    over 4.3GB capacity.
  - When ThinkPad 600, 600E, 600X, 770, 770E, 770ED, 770X, or 770Z is docked 
    to SelectaDock III and an IDE device in SelectaDock III is assigned to 
    secondary IDE channel, the IDE device is not recognized.
  - When ThinkPad 600, 600E, 600X, 770, 770E, 770ED, 770X, or 770Z is
    docked to SelectaDock I/II, the system with OS/2 Warp Version 4
    installed stops in the middle of its start up.
  - OS/2 Warp Version 4 cannot be installed on hard disks that have 
    over 8.4GB capacity.
  - When a certain type of DVD-ROM drive is installed, OS/2 Warp 4 
    takes very long time to boot.
  - When OS/2 Warp 4 is installed in a HPFS partition on ThinkPad T20, T21, 
    or T22, Trap D may occur.
 - OS/2 Warp Version 4 cannot be installed on hard disks that have over
   30GB capacity.
 - When VGA or VGA GRADD device driver is selected and installed on 
    IBM ThinkPad T21 SXGA+ (1400 x 1050) resolution model or T22 SXGA+ 
    resolution model, opening DOS fullscreen command prompt or OS/2 fullscreen 
    command prompt gets screen blank. If an external monitor is connected,
    it displays an image correctly.

This disk has the following new feature.
  - IBM ThinkPad Dock IDE controller support
 - IBM ThinkPad T23 support.

IBM ThinkPad OS/2 Warp Version 4 Install Disk 2 Update:
------------------------------------------------------------------------------
The IBM ThinkPad OS/2 Warp Version 4 Install Disk 2 Update is a
replacement of IBM OS/2 Warp Version 4 Install Disk 2.  This disk 
fixes the following problem.
  - OS/2 Warp V4 installation intermittently fails due to MOUSE$ error.
  - When OS/2 Warp 4 is installed in a HPFS partition on ThinkPad T20,
    T21, or T22, Trap D may occur.
- When VGA or VGA GRADD device driver is selected and installed on 
    IBM ThinkPad T21 SXGA+ (1400 x 1050) resolution model or T22 SXGA+ 
    resolution model, opening DOS fullscreen command prompt or OS/2 fullscreen 
    command prompt gets screen blank. If an external monitor is connected,
    it displays an image correctly

The following models are supported:
  - ThinkPad 380XD, 385XD, 380Z
  - ThinkPad 390, 390E, 390X
  - ThinkPad i Series 1720, i Series 1721 
  - ThinkPad 560X, 560Z
  - ThinkPad 600, 600E, 600X
  - ThinkPad 770, 770E, 770ED, 770X, 770Z
  - ThinkPad T20, T21, T22, T23

To determine if you have to use the OS/2 Warp Version 4 Install Disk 1
Update and Install Disk 2 Update or not, confirm if your model of
ThinkPad computer is listed above.


Released Versions
-----------------
OS/2 Warp Version 4 Install Disk 1 Update
 Version 1.00     Initial release
 Version 1.01     A problem fix
 Version 1.02     Support to IDE hard disks greater than 8.4GB capacity
 Version 1.04     A problem fix - Boot problem with a certain DVD-ROM drive
 Version 1.05     IBM ThinkPad Dock IDE controller support
                  A problem fix - Trap D problem with a HPFS partition
 Version 1.06     Support to IDE hard disks greater than 30GB capacity
                  	           IBM ThinkPad T23 support
                             A problem fix - Blank screen problem with SXGA+ models

OS/2 Warp Version 4 Install Disk 2 Update
 Version 1.00     Initial release
 Version 1.01     A problem fix - Trap D problem with a HPFS partition
 Version 1.02     A problem fix - Blank screen problem with SXGA+ models

Summary of Changes
------------------
Where: <n.nn>  Diskette version (for example, 1.00 means Version 1.00)
       (New)   New function or enhancement
       (Fix)   Correction to existing function

OS/2 Warp Version 4 Install Disk 1 Update
 <1.00>
  -(New) COPYFROMFLOPPY=1 added in CONFIG.SYS.
         IBM1S506.ADD updated.

 <1.01>
  -(Fix) IBM1S506.ADD updated.

 <1.02>
  -(Fix) IBM1S506.ADD updated
  -(Fix) IBMIDECD.FLT updated
  -(Fix) OS2DASD.DMD updated

 <1.04>
  -(Fix) IBM1S506.ADD updated
  -(Fix) IBMIDECD.FLT updated
  -(Fix) OS2DASD.DMD updated

 <1.05>
  -(New) IBM1S506.ADD updated
  -(Fix) SCREEN01.SYS updated

 <1.06>
  -(New) IBM1S506.ADD updated
  -(Fix) IBMIDECD.FLT updated
  -(Fix) OS2DASD.DMD updated
  -(Fix) SCREEN01.SYS updated

OS/2 Warp Version 4 Install Disk 2 Update
 <1.00>
  -(New) DOSCALL1.DLL updated.

 <1.01>
  -(Fix) SCREEN01.SYS updated
  -(Fix) FIXVGA.CMD   added
  -(Fix) SETVGA.CMD   updated


Install Buide
-----------------------------------------------------

<How to determine what version is installed>
These diskettes replace Install Disk 1 and Install Disk 2 that come
with OS/2 Warp Version 4 Package, and to be used at the time of 
installation. These diskettes are not to update the installed OS/2 
Warp Version 4 components. Before you start the installation of OS/2
Warp Version 4 on your ThinkPad computer, please refer to the supported
model listing in the above section and confirm if your model of IBM 
ThinkPad computer is listed there. 

<Installation of IBM OS/2 Warp Version 4.0>
OS/2 Warp Version 4 comes with three diskettes for installation. These
update disks are replacements for Disk 1 and Disk 2.

  1. Install OS/2 Warp Version 4 from the original Install Disk.
  2. When you are prompted to insert Disk 1, use Install Disk1 Update.
  3. When you are prompted to insert Disk 2, use Install Disk2 Update.
  4. Continue installing OS/2 Warp Version 4 until you are prompted to
     restart your computer for the first time.
  5. When you are prompted to restart your computer, do not proceed.
  6. Press F3 key to go to the command prompt screen.
  7. At the command prompt screen, type the following command to run
     the batch file. The batch file is available on Install Disk2
     update.
         A:\FIXVGA.CMD x:
          where, x: denotes the boot drive of OS/2 Warp Version 4.
          In other words, the drive letter to which you are installing
          OS/2 Warp Version 4.
  8. Type EXIT, then press the Enter key to go back to the previous screen.
  9. Remove the diskette from the floppy drive.
 10. Press the Enter key to restart your computer.
 11. Continue installing OS/2 Warp Version 4.
 12. When you complete the installation, open OS/2 command prompt
     screen.
      i) Double click the OS/2 System Folder on Desktop.
     ii) Double click the Command Prompts Folder.
    iii) Double click the OS/2 Window.
 13. Insert Install Disk2 Update in the floppy drive.
 14. At the command prompt screen, type the following command to run
     the batch file.
         A:\FIXVGA.CMD x:
          where, x: denotes the boot drive of OS/2 Warp Version 4.
 15. Remove the diskette from the floppy drive.
 16. Type EXIT, then press Enter key to close the command prompt screen.
 17. Properly shutdown OS/2 Warp Version 4, and restart your computer.
 18. Proceed to install OS/2 Warp Version 4 FixPack and device drivers.

 NOTES: 
   (a) When you install any version of OS/2 Warp Version 4 Base FixPak
       and OS/2 Warp Base Device Driver FixPak at version XR_D001, you 
       may be prompted whether you want to replace IBM1S506.ADD module 
       or not.  Choose no to not replace IBM1S506.ADD module 
       or your computer may not work properly. If you accidentally choose
       Yes and the module is replaced, then copy IBM1S506.ADD module 
       from the Install Disk1 Update to \OS2\BOOT directory of your 
       computer after you complete the FixPak installation.
   (b) It is strongly recommended to run FIXVGA.CMD batch file whenever you
       change display driver to VGA or VGAGRADD if your model of 
       IBM ThinkPad computer is IBM ThinkPad T21 SXGA+ (1400 x 1050)
       resolution model or IBM ThinkPad T22 SXGA+ resolution model.


<Installation of OS/2 Warp Convenience Package Version 4.51>
For OS/2 Warp Convenience Package Version 4.51, you do not have to use these
diskettes. Instead, OS/2 Warp Convenience Package comes with Installation CD,
which has the boot capability. First obtain necessary updates from OS/2 Device
Driver Pak On-line web site, install OS/2 Warp Convenience Package, and then
install updates obtained from OS/2 Device Driver Pak On-line. 
The information and updates are available from the following URL.

     http://service.software.ibm.com/os2ddpak/
  or http://service5.boulder.ibm.com/2bcprod.nsf

When the home page appears, do the following.  (The procedure is subject
to change without prior notice)
  1. If you already read and agreed to the Program License Agreement,
     click on I have read the Program License Agreement and AGREE to its terms,
     and skip to step 6 below
  2. Otherwise, click on I want to read the Program License Agreement
  3. Read the Program License Agreement
  4. Click on ACCEPT if you agree to its terms and go to the next page
  5. Click on Continue...
  6. Click on Systems
  7. Click on IBM Corporation (IBM PC Company - Mobile Systems - ThinkPad)
  8. Click on a model name of your IBM ThinkPad computer
  9. Follow the instructions.


<Installation Disk of IBM OS/2 Warp Version 3>
IMPORTANT: Several models of IBM ThinkPad do not support IBM OS/2 Warp Version 3.

The information is available from the following web site.
     
     http://service.software.ibm.com/os2ddpak/
  or http://service5.boulder.ibm.com/2bcprod.nsf

When the home page appears, do the following.  (The procedure is subject
to change without prior notice)
  1. If you already read and agreed to the Program License Agreement,
     click on I have read the Program License Agreement and AGREE to its terms,
     and skip to step 6 below
  2. Otherwise, Click on I want to read the Program License Agreement
  3. Read the Program License Agreement
  4. Click on ACCEPT if you agree to its terms and go to the next page
  5. Click on Continue...
  6. Click on OS/2 Component Updates
  7. Click on Installation Diskette Updates
  8. Click on PIIX Busmaster / >30GB Drive Support
  9. Follow the instructions.

Trademarks
----------
  * IBM, ThinkPad and OS/2 Warp are registered trademarks of IBM Corporation.

  Other company, product, and service names may be registered trademarks,
  trademarks or service marks of others.
