Kofax Driver Kit
for Ricoh IS510/IS520 (Video and SCSI) Scanners

*************************************************************************
*  (c) Copyright Kofax Image Products, 1995. All rights reserved.       *
*************************************************************************

This file contains information about the Ricoh IS510/IS520 driver kit. 
Included are important notes for using Ricoh IS510/IS520 scanners with
Kofax products, instructions for installing the drivers, and the addresses 
and phone numbers for Kofax Technical Support. 


==================================================================                                            
Important Notes - Read This Section Before You Install the Drivers
==================================================================

KIPP Developers Toolkit Users
------------------------------
For KIPP Developers Toolkit users, you must upgrade to KIPP v2.12 before
you can use these drivers.  Contact Kofax or your Kofax distributor for
more information.


Connecting the Scanner with a Video Connector
---------------------------------------------
When using an IS520 (video) scanner with a Kofax accelerator board, 
specific firmware levels are required on the PCB inside the scanner. 

To verify that your scanner has been certified to work with the Kofax 
accelerator board, look for the following label inside the lamp access 
door: 

   Kofax Compliant Single Channel Video 
   
This label verifies that the required PCB and firmware are installed 
in the scanner as follows:

   PCB/Firmware        Part Number
   
   GVS09 PCB           G4005192-SV1
   GVS09 U15 Firmware  G4005695-SV1
   GVS09 U16 Firmware  G4005696-SV1
   CPU Firmware        28458-002

If you need assistance verifying that your IS520 (video) scanner has the 
correct PCB and firmware, please contact your Ricoh service representative.
Note that these requirements do not apply to either the IS510 scanner or 
the SCSI version of the IS520.


Setting Switches on the SCSI Scanner
------------------------------------
To ensure that your Ricoh IS510/IS520 SCSI scanner operates properly when 
connected to a Kofax KF-9275 accelerator board, you must set the DIP 
switches on the rear panel of the scanner as follows:

   Switch    Setting

   1         OFF
   2         ON
   3         OFF
   4         OFF
   5         OFF
   6         OFF
   7         OFF
   8         ON

Switches 2 and 8 must be ON. Note that switch 5 can be either ON or OFF,
depending on your scanner model, as follows:

   Switch 5 ON:   IS510 (simplex scanner)
   Switch 5 OFF:  IS520 (duplex scanner)


============
Driver Files
============

The scanner drivers and other files that you need to support the Ricoh
IS510/IS520 scanners (video and SCSI) are included in KRIS5X0.EXE. 
(KRIS5X0.EXE is a self-extracting, executable file.) 

To explode KRIS5X0.EXE, copy it to a temporary directory and type 
KRIS5X0.EXE.  KRIS5X0.EXE contains these files: 

   SCANAPI.DLL     
   R520SC75.BLF
   BPR52075.OUT
   BPR520SS.OUT


============
Installation
============

To install the drivers, the files listed above must be manually copied 
to the appropriate directories. The directories you must copy the files 
to depends on whether you are using KIPP ImageControls or the KIPP 
Developers Toolkit. Follow the steps in the sections below as appropriate 
for your needs.


==================
KIPP ImageControls
==================

Follow these steps to install the drivers and files for use with KIPP
ImageControls. By default, KIPP ImageControls is installed to C:\IMGCTLS,
although this might be different on your system.

   1.  Copy the new SCNAPI.DLL file to your ImageControls BIN directory.
   2.  Copy the new .OUT files to your ImageControls DRIVER directory.
   3.  Copy the new .BLF files to your ImageControls DRIVER directory.
   4.  Reboot your system.
   5.  Use the Kofax Configuration Program from your Windows Control Panel
	   to configure your scanners.


========================
KIPP Developers Toolkit
========================
   
Follow these steps to install the drivers and files for use with the KIPP
Developers Toolkit. By default, the KIPP Developers Toolkit is installed
to C:\KIPP, although this might be different on your system.

Note that you must have KIPP v2.12 installed on your system to use the
drivers.

   1.  Copy the new .OUT files to your KIPP DRIVER directory.
   2.  Copy the new .BLF files to your KIPP DRIVER directory.
   3.  Reboot your system.
   4.  From the KIPP BIN directory, run KIPPCFG to configure your
	   scanners.


==========
References
==========

	KIPP ImageControls Technical Reference Manual
	KIPP Developers Toolkit Technical Reference Manual


=======================
Kofax Technical Support
=======================

If you need further assistance, contact your Kofax distributor, or 
contact the Kofax Technical Support Staff at:

   Headquarters                  European Headquarters

   Kofax Image Products          Kofax Image Products
   3 Jenner Street               Rue Capouillet 19
   Irvine, CA 92718              1060 Brussels, Belgium

   (714) 727-1733 (voice)        +32-2-536-8630 (voice)
   (714) 727-1941 (rotary)       +32-2-536-8601 (fax)
   (714) 727-3144 (fax)          +32-2-536-8674 (BBS)
   (714) 727-3538 (BBS)

Or, you can use the following Kofax Internet connection:

   support@kofax.com

You can also use the Kofax QuickFax service to receive data sheets,
configuration guides, and other types of Kofax literature. The Kofax
QuickFax service is available 24 hours a day, 7 days a week. To use
QuickFax, dial the number below and follow the instructions presented
to you:

   (714) 727-0788 (QuickFax) 
