Windows NT 3.5x Installation

Once Windows NT 3.5x has been installed on your system, follow the procedure
listed below to install the Microsoft Windows NT 3.5x display driver.

1.	Select Control Panel from the Main group.
2.	Select the Display icon.
3.	Select the Change Display Type button in the Display Settings dialog
        box.
4.	Select the Change button from the Display Type dialog box.
5.	Select the Other button at the Select Device dialog box.
6.      Place the driver cdrom into cdrom drive and type

        "5465_agp\nt\nt35"

        then click OK. In the Models window the Cirrus Logic driver, Cirrus
        Logic VisualMedia Accelerator is displayed.

7.      Next, select the Install button and click Yes to begin the driver
        installation.
8.      When the Windows NT Setup dialog box appears again, select Drive d:
        and click Continue.
9.	When the Installing Driver dialog box appears click OK and click OK
        again at the next dialog box.
10.	You must now restart Windows NT 3.5x to use the Windows NT 3.5x
        display driver. If you select the Don't Restart Now option, your
        Windows NT driver will not be installed until after you shut down your system.
11.	If, after installation, the Invalid Display Settings dialog box
        appears, click OK and verify or change the information viewed in the
        Display Settings dialog box. See the Selecting Resolution and Color
        Depth section below for additional information on display settings.

Selecting Resolution and Color Depth

To select resolution and color depth for the Windows NT version 3.5x display
driver, follow the procedure listed below.

1.	Select Control Panel from the Main group.
2.	Select the Display icon.
3.	Select Color Palette to change between 256 colors, 65,536 colors,
        16,777,216 colors and True Color.

NOTE:  Not all colors are available for all resolutions.

4.	To select desktop resolution size, go to the Desktop area and use the
        slide bar to change resolution from 640x480, 800x600, 1024x768,
        1152x864, 1280x960, 1280x1024 and 1600x1200.
5.	Select Test to test the resolution.

If the display test screen was good then select Yes when the Test Mode dialog
box appears. Windows NT 3.5x will prompt you to restart Windows NT 3.5x.

If the display test screen was bad then select No.  Windows NT will give you
an error message.



Windows NT 4.0 Installation

Once Windows NT 4.0 has been installed on your system, follow the procedure
listed below to install the Microsoft Windows NT 4.0 display driver.

1.	Right click on the Windows NT desktop (the Windows background where
        no windows or icons are displayed) and select Properties.
2.	At the top of the dialog box, click on the Settings tab.
3.	At the bottom of the Settings display screen, click on the Display
        Type button.
4.	Click on the Change button in the Adapter Type box.
5.	In the Change Display screen, click on the Have Disk button.
6.      place the driver cdrom in cdrom drive and follow the on-screen
        instructions.
7.      When Windows NT asks where the driver is located, type D:

The Windows NT 4.0 driver will be installed in the Windows NT System
directory.
To configure the Windows NT 4.0 driver, follow the procedure listed in the
next section.

Configuring the Windows NT 4.0 Driver

To configure your Windows NT 4.0 driver once it is installed, follow the next
two procedures listed in consecutive order.

Selecting a Monitor

To enable the Windows NT 4.0 Settings dialog box, where you can change your
driver and monitor configurations, to show only those monitor configurations
that your monitor can actually do, a Monitor Selection utility is available.

1.	Right click on the Windows NT desktop (the Windows background where
        no windows or icons are displayed) and select Properties.
2.	From the Display Properties dialog box, click on the Monitor
        Selection tab, located at the top of the dialog box.
3.	Choose your Monitor Brand and Monitor Model by clicking on the
        respective arrow buttons to display the monitor drop-down boxes.

After selecting your Monitor Brand and Monitor Model, the highest refresh
rate, which your monitor is capable off, will display in the Monitor Capable
Refresh Rates section of the Monitor Selection dialog box.

Changing the Display Settings

After completing the above monitor selection, you are now ready to configure
all the display settings of the Windows NT 4.0 driver.

1.	From the Display Properties dialog box, you can change your driver
        and monitor configurations. Click on the Settings tab, located at the
        top of the dialog box.
2.	Adjust the settings using the drop-down boxes and slider bars.
        Depending on your monitor, the Windows NT 4.0 driver can display the
        following resolutions: 640x480, 800x600, 1024x768, 1152x864, 1280x960,
        1280x1024 and 1600x1200.
3.	Follow the on-screen prompts to complete the Windows NT 4.0 driver or
        monitor configuration.



