                      FastTrak S150 SX4 NetWare Driver
                           Version 1.02.30.01
                      For Novell NetWare 5.1 6.0 and 6.5

[INTRODUCTION]

1.1 Foreward

This procedure applies to FastTrak S150 SX4 adapters running under 
Novell NetWare 5.1/6.0/6.5 operating systems. This driver
supports hard disk drives greater than 137GB.
 

1.2 Module Check

The operating system must be running a IDEHD.CDM module dated 08/16/2002 
or later in order to support hard disk drives greater than 137GB.

    1. On your NetWare computer, run DOS.
 
    2. Go to directory C:\NWSERVER\DRIVERS.

    3. Check the date of the IDEHD.CDM file.

       If the date is 08/16/2002 or later, continue with the driver
       installation.

       If the date is earlier than 08/16/2002, download and install the 
       latest Service Pack from http://support.novell.com. Then continue
       with the driver installation.


[INSTALLATION]

2.1 Prepare a Driver Diskette

You will use a diskette to load the new FastTrak S150 SX4 driver onto your PC.

    1. Obtain a new, formatted diskette and label it "FastTrak S150 SX4 Driver Disk."
       Insert it into your PC's floppy drive.

    2. Extract the contents of the driver file you downloaded from the
       Promise website onto your diskette.


2.2 To install the FastTrak S150 SX4 driver into a NEW system:

    1. Start the Netware 5.1/6.0/6.5 installation as you normally would.

    2. When you reach the point in the installation where you install storage 
       adapters, choose "Modify" in the "Options" window and press ENTER.

    3. Highlight the "Storage Adapters" field and press ENTER.

    4. Delete FTSX.HAM in the list. 

    5. Press the INSERT key on your keyboard to "Add a device".

    6. Insert the FastTrak S150 SX4 Driver Disk into your A: floppy drive.

    7. Press the insert key again to "Add an unlisted driver".

    8. Press F3 and type "A:\" in the "Specify a directory path:" window.
       Press ENTER.

    9. The FTSX.HAM driver should be listed in the "Select a driver to
       install:" window. Press ENTER to select this driver.

   10. If you need to install any additional drivers for other storage
       adapters, choose "Yes" in the "Do you want to select an additional 
       storage driver?" window. If not, choose "No".

   11. Choose "Return to driver summary" in the "Additional Driver Options"
       window and press enter.

   12. Choose "CONTINUE" in the options window and press ENTER.

   13. Continue the installation as you would normally.



2.3 To install the  driver into an EXISTING system(for Novell NetWare 5.1/6.0):

    1. From the System Console type "Modules FTSX" to check whether there is
       an old version driver. If there has one, type "unload FTSX" to unload
       it before you install the new driver.

    2. From the System Console type "NWCONFIG".

    3. Choose "Driver Options".

    4. Choose "Configure disk and storage device drivers".

    5. Choose "Select an additional driver".

    6. Press the INSERT key on your keyboard.

    7. Insert the FastTrak S150 SX4 Driver Disk into your A: floppy drive.

    8. Press F3 and type "A:\" in the "Specify a directory path:" window.
       Press ENTER.

    9. The FTSX.HAM driver should be listed in the "Select a driver to
       install:" window. Press ENTER to select this driver.

   10. Choose "Yes" when asked if you want to copy this driver.

   11. In the "Specify a server boot path(where SERVER.EXE will be)" window,
       it will show default string like "C:\NWSERVER", just press ENTER.

   12. In the "Driver FTSX Parameter Actions" window, choose "Save parameters 
       and load driver"	

   13. If you need to install any additional drivers for other storage
       adapters, choose "Yes" in the "Do you want to select an additional 
       disk driver?" window. If not, choose "No".

   14. Exit NWCONFIG to complete the installation of driver.


2.4 To install the  driver into an EXISTING system(for Novell NetWare 6.5):

    1. From the System Console type "Modules FTSX" to check whether there is
       an old version driver. If there has one, type "unload FTSX" to unload
       it before you install the new driver.

    2. From the System Console type "HDETECT".

    3. Highlight the "Storage Adapters" field and press ENTER.

    4. choose "Modify" in the "Options" window and press ENTER.	

    5. Press the INSERT key on your keyboard to "Add a device".

    6. Insert the FastTrak S150 SX4 Driver Disk into your A: floppy drive.

    7. Press the insert key again to "Add an unlisted driver".

    8. Press F3 and type "A:\" in the "Specify a directory path:" window.
       Press ENTER.

    9. Choose "Return to driver summary" in the "Additional Driver Options"
       window and press enter.

   10. Choose "CONTINUE" in the options window and press ENTER.

   11. Continue the HDETECT as you would normally.

