**************** Installation Note **************************************


The CD-ROM driver in the AUTOEXEC.BAT file must be loaded before
any other executable files.  Please ensure that the CORELCDX driver is
located at or near the top of the AUTOEXEC.BAT file.

CORELCDX driver should be configured as follows:

C:\SHTLMAN\CORELCDX /d:ASPI_CD

*************************************************************************
 For os/2 3.0 WARP installation:
1.Enter OS/2 environment  
2.Select floppy A device
3.Select \os2 directory 
4.Run "install" icon
5.If you can't finish the install procedure then your OS/2 system may
  have some bugs ,you can use the following procedures to install the
  external CD-ROM:
  a. Enter the OS/2 full screen,copy the "EPIACD.ADD" and
     "EPIACD.PKG"(from A:\SHUTTLE\OS2) to C:\OS2
  b. Enter OS/2 sytem editor,open the C:CONFIG.SYS,copy one 
     "BASEDEV=EPIACD.ADD" line to the CONFIG.SYS file then save it
  c. Shutdown OS/2 system,connect correctly the external CD-ROM then
     power on the systen.
 
 Notes:
1.If we use ACER 525E or ACER 743E for the external device,then we must
  set the device as "SLAVER"(from the jumper).
2.The I/O address must be 378H.

***************************************************************************
 For installing OS/2 3.0 WARP from external CD-ROM via EPIA interface 
 
1. Make a Backup of your OS/2 Warp Installation Disk and Disk 1
2. TURN OFF PC,insert the backup copy of your OS/2 Warp installation 
   diskette into drive A             
3. TURN ON PC,when prompted to do so,insert the backup copy of your     
   OS/2 WARP diskette 1 into drive A
4. The boot process will proceed for a short while,but then the message   
   "OS/2 is unable to locate any CD drive" will be displayed.When you see
   this error,press "ENTER" and you will be returned to the OS/2 A:] prompt. 
5. At the A:] prompt type "TEDIT CONFIG.SYS".You will see the contents of     
   the Config.sys file displayed,Hit the <ESC> key to go into Edit mode.
   Locate the area where " BASEDEV= "statements are listed and insert the 
   line "BASEDEV=EPIACD.ADD".
6. Copy the "EPIACD.ADD " file from the EPIA installation diskette to the 
   OS/2 Diskette 1.(IF there is insufficient room on the diskette1 to do 
   this you will have to move one of the *.ADD drivers you are not currently 
   using (AHA1540.ADD for example) and delete its corresponding BASEDEV
   statement from the Config.sys file on OS/2 diskette 1.
7. Power off PC.Connect the external CD-ROM from EPIA interface.Insert the 
   backup copy of installation diskette in drive A:] and power on PC and 
   external CD-ROM.
8. Proceed with the OS/2 Warp installation according to the instructions
   suplied,inserting the modified backup copy of your diskette 1 when 
   prompted to do so.
9. When you finish the whole procedures of OS/2 3.0 Warp,you can see the
   external CD-ROM from the "DEVICE" icon as the " D drive".


-------------------------------------------------------------------------- 
       INSTALLING EPIA DRIVERS UNDER WINDOW'S 95(Final BETA ver.)
1. Launch Windows'95
2. Double click on "MY COMPUTER" icon
3. Insert EPIA shuttle Manager diskette in drive A:
4. Double click on 3 1/2 Floppy [A:]
5. You should now double click on INSTALL.BAT.This will install shuttle
   manager as normal. 
  * Except  do not press CDRL ALT DEL to reboot just hit any other key *
6. Then remove the install utility diskette from A:
7. Single click on START
8. Single click on SHUT DOWN
9. Finally double click on RESTART
10. Windows'95 will reboot and install the SHUTTLE device drivers as usual
    under DOS


