
                OS/2 1.3 and 2.0 driver for Canon BJ-Series Printers
                ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
    The Canon BJ-Series Printer Driver for OS/2 PM supports the following
Canon printers:

     Canon BJ-200       Black printing
     Canon BJ-230       Black printing
     Canon BJ-300       Black printing
     Canon BJ-330       Black printing
     Canon BJC-600      Black or Colour (CMYK) printing
     Canon BJC-800      Black or Colour (CMYK) printing

    The BJ-300 & BJ-330 are supported using the Proprinter emulation. The 
    BJ-200, BJ-230, BJC-600 and BJC-800 are supported in their native mode.

    If you are installing this driver as an upgrade for an older version,
    or if this is a completely new installation, you should first read
    the installation notes in INSTALL.TXT (please ignore an icon for model 
    XXXXXX which may appear in the driver file window during installation).
   
    In addition, you should ensure that your printer is set up correctly 
    for use with the driver.

    If you received this driver in a ZIP file, or the driver disk has been
    copied using DOS instead of OS/2, you must reconstruct the driver disk
    BEFORE installing the driver. To do this, you should run the OS/2 command
    RESETEA on the driver disk. If you do not do this, the driver will not
    install correctly on your system.


    This file contains the following:
        1. Release notes
        2. Printer setup notes


        1. RELEASE NOTES
        ~~~~~~~~~~~~~~~~

    Release Notes for Version 1.4
    ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

        Support for the BJ-100 printer has been added

        Support for the BJ-200e printer has been added
 

    Release Notes for Version 1.3
    ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

        The names of .INI file records now have the OS/2 2.1 format (i.e.
        the prefix is PM_DD_).

        The following errors have been corrected:
  
        1. Garbage was printed on the BJC-600 (Dip Switch 12 OFF) when using 
           WordPerfect 5.2.

        2. The characters 'AB' were spuriously printed when printing a plain
           text file by using 'Drag-and-Drop' or the 'copy' command from an
           OS/2 prompt.

           A side-effect of the correction is that the final page is ejected
           at completion of the job (previously the user had to use the FF 
           key).

        3. 'Forms Mis-match' was sometimes not reported when using the BJ-300.
        
        
    Release Notes for Version 1.2
    ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

        Support for the BJC-600 printer has been added


    Release Notes for Version 1.1
    ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

        Support for the BJ-230 printer has been added


    Release Notes for Version 1.0
    ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

        1. Changed the default for BJ-300/330 Paper Feed to be Cut Sheet

        2. Changed the default to Colour Printing ON for the BJC-800

        3. Added internal fonts and Font Card support for the BJ-3xx printers.

        4. Added support for the BJ-200 in its 'native' mode.


    Release Notes for Version Alpha 1.0
    ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
        The driver does not support the use of internal fonts or font cards
    on the BJ-300 and BJ-330. Only ATM fonts (supplied with OS/2) can be
    used at present.


    2. Setting up your BJ printer for use with the driver
    ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

    BJ-300/330:
    ~~~~~~~~~~~

        This driver is for the BJ-300 and BJ-330 using the Proprinter
    Emulation mode. In order to use the driver with either of these
    printers, you must ensure that your printer has been set to use
    this emulation.

    You must set the DIP switches (located at the back of the printer)
    as instructed in your BJ-300/330 User's Manual so that:
            Switch 1-1 and 1-2 are ON.

    If you do not do this, and your printer is set to the wrong emulation,
    garbage will be produced by the driver.

    BJ-200, BJ-230:
    ~~~~~~~~~~~~~~~

        This driver supports the BJ-200 and BJ-230 in their 'native' (BJ-10)
    control mode. You must check that the printer DIP switches are set
    correctly before printing using the driver.

    You must set the DIP switches (as described in your user's manual) so that
    Switch 12 is up (off).

    To ensure that the horizontal print position is correct, you should also
    set Switch 1 as required for the paper size you are using.


    BJC-600:
    ~~~~~~~~

        This driver supports the BJC-600 in its native mode. Before printing
    using this driver you must set the printer into its LQ 2550 Emulation.
    You should check that the printer DIP switches are set correctly before
    printing using the driver.

    You must set the DIP switches as instructed in your BJC-600 User's Manual
    so that: Switch 12 is up (ON).

    To ensure that the horizontal print position is correct, you should also
    set the other DIP switches as required for the paper size you are using.


    BJC-800:
    ~~~~~~~~
        No special printer settings are required for this printer.

